[Check_mk (english)] Getting an Allnet ALL4500 to work with CMK

Jonas Neumann cmk at tschanness.de
Tue Feb 17 15:09:39 CET 2015


Hi,
thank you. I'll have a look into it and reply back :)

Jonas

On Tue, Feb 17, 2015 at 3:00 PM, Andreas Döhler
<andreas.doehler at gmail.com> wrote:
> Inside the actual GIT is an very new Allnet check with special agent
> available.
> It would be good if you have a look at this and the actual check to know
> what is missing in your setup.
>
> Special Agent:
> http://git.mathias-kettner.de/git/?p=check_mk.git;a=blob;f=agents/special/agent_allnet_ip_sensoric
> CMK Check for this agent:
> http://git.mathias-kettner.de/git/?p=check_mk.git;a=blob;f=checks/allnet_ip_sensoric
>
> Best regards
> Andreas
>
> Marcel Schulte <schulte.marcel at gmail.com> schrieb am Tue Feb 17 2015 at
> 14:54:45:
>
>> I ment "checktype", not "checkmate" ;-)
>>
>>
>> Marcel Schulte <schulte.marcel at gmail.com> schrieb am Di., 17. Feb. 2015
>> 14:49:
>>
>>> Looks normal - but you have to develop your checkmate "sensoren" because
>>> cmk does not know what to do with the received data:
>>> http://mathias-kettner.com/checkmk_devel_agentbased.html
>>>
>>> Marcel
>>>
>>>
>>> Jonas Neumann <cmk at tschanness.de> schrieb am Di., 17. Feb. 2015 13:37:
>>>
>>>> Hi Marcel,
>>>> thanks for the fast answer :)
>>>> CMK only shows the Ping output nothing else. If I open the service Tab
>>>> it shows nothing.
>>>> The Host is configured a normal Host in WATO with the datasource
>>>> Program as followed:
>>>> ssh root at 10.35.12.11 /root/check_mk_agent.sensormeter
>>>>
>>>> The outpuf of cmk -d:
>>>>
>>>> OMD[rcs_monitor]:~$ cmk -d mlakcpkp01
>>>> <<<check_mk>>>
>>>> Version: 1.2.4
>>>> AgentOS: linux-embedded
>>>> <<<sensoren>>>
>>>> P Sensor 1: Temperatur 22.30
>>>> P Sensor 2: Temperatur 25.71
>>>> P Sensor 3: Temperatur 20.40
>>>>
>>>> Thank you for your Time!
>>>>
>>>> Jonas
>>>>
>>>> On Tue, Feb 17, 2015 at 1:29 PM, Marcel Schulte
>>>> <schulte.marcel at gmail.com> wrote:
>>>> > Hi Jonas,
>>>> >
>>>> > What exactly does not work when you use your own "agent"?
>>>> > How do you configure the host in CMK?
>>>> > Does "cmk -d HOSTNAME" output anything? Could you post the output?
>>>> >
>>>> > Regards,
>>>> > Marcel
>>>> >
>>>> > Jonas Neumann <cmk at tschanness.de> schrieb am Tue Feb 17 2015 at
>>>> > 13:15:08:
>>>> >>
>>>> >> Hello,
>>>> >> I have an Allnet ALL4500 Applicane wich does not deliver its values
>>>> >> via SNMP. It is possible to Access the device via SSH but i was not
>>>> >> able to get the linux agent to work. I tried to programm a small
>>>> >> "Agent", wich only outputs the Sensor values:
>>>> >>
>>>> >> <<<check_mk>>>
>>>> >> Version: 1.2.4
>>>> >> AgentOS: linux-embedded
>>>> >> <<<sensoren>>>
>>>> >> P Sensor 1: Temperatur 22.55
>>>> >> P Sensor 2: Temperatur 25.80
>>>> >> P Sensor 3: Temperatur 19.64
>>>> >>
>>>> >> This does not work either :). I thought about using NRPE but it is
>>>> >> superseeded by MRPE (wich requires the agent, right?). So I'm stuck
>>>> >> and don't know how to proceed. Any advice on how to get this working
>>>> >> as easy as possible? Thank you in advance!
>>>> >>
>>>> >> Jonas
>>>> >> _______________________________________________
>>>> >> checkmk-en mailing list
>>>> >> checkmk-en at lists.mathias-kettner.de
>>>> >> http://lists.mathias-kettner.de/mailman/listinfo/checkmk-en
>>
>> _______________________________________________
>> checkmk-en mailing list
>> checkmk-en at lists.mathias-kettner.de
>> http://lists.mathias-kettner.de/mailman/listinfo/checkmk-en


More information about the checkmk-en mailing list