[omd-users] Fresh Install of OMD 1.20 on CentOS 6.6 64Bit - Livestatus Not Running

Peter Shankland pshankland at gmail.com
Thu May 7 16:13:03 CEST 2015


I had no idea there was a command 'omd config <sitename>'! Yes that was it,
livestatus is disabled as default so just had to stop the site, enable
livestatus through omd config and then start the site again.

Thanks for the help

On 7 May 2015 at 15:00, May,Allen <AMAY at vha.com> wrote:

>  Looks like it is configured.
>
> Can you see the port listening or telnet to it?
>
>
>
> # lsof | grep '*:6557'
>
> xinetd     2187      root    6u     IPv6              18433
> 0t0        TCP *:6557 (LISTEN)
>
>
>
> From this part:
>
> # TCP port number. Can be configure via LIVESTATUS_TCP_PORT
>
>         port            = 6557
>
>
>
>
>
> Maybe there’s a setting in ‘omd configure’ I forgot about.  It’s been
> awhile since I set it up.
>
>
>
>
>
>
>
> *From:* Peter Shankland [mailto:pshankland at gmail.com]
> *Sent:* Thursday, May 07, 2015 8:56 AM
> *To:* May,Allen
> *Cc:* omd-users at lists.mathias-kettner.de
> *Subject:* Re: [omd-users] Fresh Install of OMD 1.20 on CentOS 6.6 64Bit
> - Livestatus Not Running
>
>
>
> xinetd is running and the following is
> my /opt/omd/sites/SlaveRPLS/etc/mk-livestatus/xinetd.conf
>
>
>
> service livestatus
>
> {
>
>         type            = UNLISTED
>
>         socket_type     = stream
>
>         protocol        = tcp
>
>         wait            = no
>
>
>
>         # limit to 100 connections per second. Disable 3 secs if above.
>
>         cps             = 100 3
>
>
>
>         # set the number of maximum allowed parallel instances of unixcat.
>
>         # Please make sure that this values is at least as high as
>
>         # the number of threads defined with num_client_threads in
>
>         # etc/mk-livestatus/nagios.cfg
>
>         instances       = 500
>
>
>
>         # limit the maximum number of simultaneous connections from
>
>         # one source IP address
>
>         per_source      = 250
>
>
>
>         # Disable TCP delay, makes connection more responsive
>
>         flags           = NODELAY
>
> # configure the IP address(es) of your Nagios server here:
>
> #       only_from       = 127.0.0.1 10.0.20.1 10.0.20.2
>
>
>
> # ----------------------------------------------------------
>
> # These parameters are handled and affected by OMD
>
> # Do not change anything beyond this point.
>
>
>
> # Disabling is done via omd config set LIVESTATUS_TCP [on/off].
>
> # Do not change this:
>
>         disable         = no
>
>
>
> # TCP port number. Can be configure via LIVESTATUS_TCP_PORT
>
>         port            = 6557
>
>
>
> # Paths and users. Manual changes here will break some omd
>
> # commands such as 'cp', 'mv' and 'update'. Do not toutch!
>
>         user            = SlaveRPLS
>
>         server          = /omd/sites/SlaveRPLS/bin/unixcat
>
>         server_args     = /omd/sites/SlaveRPLS/tmp/run/live
>
> # ----------------------------------------------------------
>
> }
>
>
>
> There is no port listed so should I add?
>
>
>
> Thanks.
>
>
>
> On 7 May 2015 at 14:48, May,Allen <AMAY at vha.com> wrote:
>
> Is your livestatus set and xinetd restarted?  Disable = yes  may be the
> default…can’t remember.
>
>
>
>
>
> # cat /etc/xinetd.d/livestatus
>
> service livestatus
>
> {
>
>         type            = UNLISTED
>
>         port            = 6557
>
>         socket_type     = stream
>
>         protocol        = tcp
>
>         wait            = no
>
> # limit to 100 connections per second. Disable 3 secs if above.
>
>         cps             = 100 3
>
> # set the number of maximum allowed parallel instances of unixcat.
>
> # Please make sure that this values is at least as high as
>
> # the number of threads defined with num_client_threads in
>
> # etc/mk-livestatus/nagios.cfg
>
>         instances       = 500
>
> # limit the maximum number of simultaneous connections from
>
> # one source IP address
>
>         per_source      = 250
>
> # Disable TCP delay, makes connection more responsive
>
>         flags           = NODELAY
>
>         user            = lab
>
>         server          = /omd/sites/lab/bin/unixcat
>
>         server_args     = /omd/sites/lab/tmp/run/live
>
> # configure the IP address(es) of your Nagios server here:
>
> #       only_from       = 127.0.0.1 10.0.20.1 10.0.20.2
>
>         disable         = no
>
> }
>
> *From:* omd-users-bounces at lists.mathias-kettner.de [mailto:
> omd-users-bounces at lists.mathias-kettner.de] *On Behalf Of *Peter Shankland
> *Sent:* Thursday, May 07, 2015 8:42 AM
> *To:* omd-users at lists.mathias-kettner.de
> *Subject:* [omd-users] Fresh Install of OMD 1.20 on CentOS 6.6 64Bit -
> Livestatus Not Running
>
>
>
> Hi all,
>
>
>
> As the subject suggests, I have created two new CentOS 6.6 64Bit servers
> and installed OMD 1.20 on them ready to use one as a master and the other
> as a slave. The installations appear to have gone fine and I have managed
> to configure the distributed monitoring and the config has gone from the
> master to the slave.
>
>
>
> The issue I have is with Livestatus as nothing is getting reported back to
> the master. Also, when I run netstat -ln|grep 6557 on both machines,
> nothing is reporting.
>
>
>
> My nagios.log shows the following:
>
>
>
> [1431005132] livestatus: Finished initialization. Further log messages go
> to /omd/sites/SlaveRPLS/var/nagios/livestatus.log
>
> [1431005132] Event broker module
> '/omd/sites/SlaveRPLS/lib/mk-livestatus/livestatus.o' initialized
> successfully.
>
> [1431005132] Finished daemonizing... (New PID=1444)
>
> [1431005132] TIMEPERIOD TRANSITION: 24X7;-1;1
>
> [1431005132] TIMEPERIOD TRANSITION: 24x7;-1;1
>
> [1431005132] TIMEPERIOD TRANSITION: none;-1;0
>
> [1431005132] TIMEPERIOD TRANSITION: thruk_24x7;-1;1
>
> [1431005132] logging initial states
>
>
>
> and my livestatus.log shows this:
>
>
>
> 2015-05-07 14:25:15 deinitializing
>
> 2015-05-07 14:25:15 Waiting for main to terminate...
>
> 2015-05-07 14:25:17 Waiting for client threads to terminate...
>
> 2015-05-07 14:25:17 Logfile cache: flushing complete cache.
>
>
>
> The above is happening on both machines.
>
>
>
> So, I can see that livestatus is not running but not sure how to start
> debugging the issue from here as first time using it and OMD - any
> suggestions would be useful.
>
>
>
> Thanks.
>    ------------------------------
>
> ---------------------------------------------------------------------------
> The information transmitted in this e-mail and in any replies and forwards
> are for the sole use of the above individual(s) or entities and may contain
> proprietary, privileged and/or highly confidential information. Any
> unauthorized dissemination, review, distribution or copying of these
> communications is strictly prohibited. If this e-mail has been transmitted
> to you in error, please notify and return the original message to the
> sender immediately at the above listed address. Thank you for your
> cooperation.
>
>
>
> ------------------------------
> ---------------------------------------------------------------------------
> The information transmitted in this e-mail and in any replies and forwards
> are for the sole use of the above individual(s) or entities and may contain
> proprietary, privileged and/or highly confidential information. Any
> unauthorized dissemination, review, distribution or copying of these
> communications is strictly prohibited. If this e-mail has been transmitted
> to you in error, please notify and return the original message to the
> sender immediately at the above listed address. Thank you for your
> cooperation.
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.mathias-kettner.de/pipermail/omd-users/attachments/20150507/c48834c3/attachment.html>


More information about the omd-users mailing list